相场法模拟GaAs衬底上InGaAs异质结表面形貌

本工作采用相场法模拟GaAs衬底上生长的In_(0.3)Ga_(0.7)As多层异质结构薄膜表面。通过引入多序参量,使用半隐性傅里叶谱方法求解Cahn-Hilliard方程可以求得带缓冲层结构的薄膜表面形貌。计算结果模拟了薄膜生长过程,研究显示,使用In0.15-Ga0.85As缓冲层,厚度从1nm增加到4nm,薄膜表面临界波长从34nm提升到80nm。随着缓冲层的厚度从1nm增加到10nm,使用正弦波表面的模拟结果显示,薄膜表面粗糙度从2.87nm下降到0.43nm,随机叠加波表面的模拟结果也类似,表面粗糙度从1.21nm下降到0.18nm。热力学分析和应变分布分析可以解释缓冲层对薄膜表面形貌演化的作用。该模拟计算方式对设计缓冲层结构有很大的帮助,模拟计算的结果可以与实验相比对。     

Ordinary Portland Cement composition for the optimization of the synergies of supplementary cementitious materials of ternary binders in hydration processes

The synergistic effects of using several supplementary cementitious materials (SCMs), such as Blast Furnace Slags plus Limestone Filler or Fly Ashes, depend on the OPC composition. When using an OPC which is poor in C₃A and alkalis in ternary formulations, a similar initial strength gain to that of a plain OPC is detected and at longer hydration ages, the formation of monocarboaluminate, hemicarbonate and hydrotalcite instead of monosulphate can be seen. If an OPC with a higher C₃A content and alkalis is used with SCMs, the higher availability of Al causes the early formation of monocarboaluminate and a lower initial strength gain. At longer hydration times, in ternary blends with both OPCs, the mechanical strengths are higher and the C-S-H gels formed are richer in Al and poorer in C/S ratio with a subsequent lowering of the alkali content in the pore solution when compared to that in plain OPC.     

Hydrogen sorption properties of V85Ni15

An alloy with nominal composition V₈₅Ni₁₅ was prepared in a vacuum induction melting apparatus. The chemical analysis of the sample showed a V (Ni) content of 82.63 (15.68) at% and small contaminations by carbon and aluminum. XRD measurements confirmed that the bcc Ni-V solid solution phase is the main constituent of the sample. However, a minor impurity (approximately 6.5 wt%) due to the precipitation of the sigma NiV_3-x phase is present in the sample.Hydrogen sorption measurements extending from 150 °C up to 400 °C in a wide pressure range (up to 90 bar) were performed. Upon hydrogenation below 250 °C, one observes the subsequent presence of an α phase and of two hydride phases with different values of dehydrogenation enthalpy: ΔH_dehydr = 21 ± 1 kJ/mol for 0.15 ≤ H/M ≤ 0.30 and ΔH_dehydr = 26 ± 2 kJ/mol for 0.53 ≤ H/M ≤ 0.59. Above 300 °C, there is no evidence of the formation of hydrides and only an α phase is present up to the maximum measured composition, with a hydrogenation enthalpy ΔH_hydr = 10.0 ± 0.5 kJ/mol.     

桁架式火星探测器的着陆缓冲特性分析

着陆缓冲机构是着陆器实现行星探测软着陆的关键部位之一,它的缓冲性能直接关系到着陆器是否能安全地在行星表面实现软着陆。根据某院提供的火星着陆器模型,在三维建模软件中建立着陆器的合理简化模型,为了提高分析着陆器软着陆过程冲击响应的准确性,采用MSC公司的Patran/Dytran有限元软件,用瞬态动力学的方法对着陆器的缓冲性能进行分析。仿真结果与试验数据十分吻合,着陆器的缓冲和传力性能良好。因此,采用拉杆缓冲的桁架式火星着陆器是可行的,仿真结果与试验数据也为今后的火星探测提供了参考。     

多次真空固溶处理对GH1131高温合金组织和力学性能的影响

利用真空高压气淬工艺研究了GH1131高温合金经1100~1170 ℃范围内多次真空固溶处理后的组织和力学性能。结果表明,固溶态组织包含奥氏体晶粒和颗粒状碳化物,且随着固溶温度的升高,晶粒度稍有增大趋势。GH1131高温合金经多次真空固溶处理后组织均匀,常温与高温力学性能稳定,经1100 ℃+1130 ℃+1170 ℃三次真空固溶处理后,晶粒度维持了6~8级,900 ℃高温抗拉强度达到200 MPa。     

组合赋权的TOPSIS在冲击地压危险性评价中的应用

为了合理准确地评价煤矿冲击地压危险性,在现有评价冲击地压危险性实例的基础上,从煤矿地质因素和开采因素2个方面,选取10个主要的影响指标,利用熵权法和指标相关性权重法分别计算影响冲击地压危险性的各评价指标权重,再根据组合赋权的方法得出各指标的综合权重,构建基于逼近理想解理论的冲击地压危险性评价模型。以重庆砚石台煤矿为例,选取20组评价冲击地压危险性样本数据进行分析,确定评价冲击地压危险性的最优和最劣状况,然后计算出各个评价方案与最优和最劣状况的距离,最后综合最优与最劣距离,确定评价对象的相对贴近度。应用结果表明:评价结果与实际情况一致,且该模型相较其他模型的评价结果更加科学准确,表明该方法有良好的实用价值。     

汽车用钢弹性模量测试探讨

采用静态拉伸试验方法对系列汽车用钢材料进行测试，得到了汽车用钢材料的弹性模量，分析了强化方式、轧制方向、塑性变形等对材料弹性模量的影响。结果表明：强化方式影响材料的弹性模量，固溶强化的汽车用钢材料弹性模量最大；材料的弹性模量表现出各向异性特点，垂直于轧制方向的弹性模量最大；塑性变形降低材料的弹性模量。研究结果为工程设计、冲压模拟、碰撞模拟、回弹模拟等提供计算依据。